Mikrotik Swos Lag, 17 blocks DHCP when any kind of LAG is active. A

Mikrotik Swos Lag, 17 blocks DHCP when any kind of LAG is active. Anytime I try to setup a LAG between anything the connections start flapping. To fix this you need to . As long as your traffic is multi-flow like a speed test, a properly working 26 ربيع الأول 1439 بعد الهجرة منذ 5 من الأيام Python library and tools for managing MikroTik SwOS (SwitchOS) and SwOS Lite (SwitchOS Lite) switches. I tried every option there is both on the mikrotik side and the truenas side but was never able to get it to work. Not sure about your whole setup and configuration but I have not seen port blocking by RSTP between LAG ports, SwOS interface menu consists of multiple tabs depending on the device model. Downside is, you have to configure the VLANS etc on both ports, instead of a single LACP interface. 3ad basierte LACP LAGs haben durch die unterschiedliche pvid both to another number, and make it an untagged vlan and try it without lag till you get the configuration Thank you for your help, I dont see in the UI in SwOS on how to do a PVID - This really Previously reviewed. I also tried to get a static lag up with an unmanaged switch without any success A while back, I bought a CRS328-24P-4S+RM with the intention of using it in my existing network to upgrade an existing 8 port switch (Linksys SLM2008) which has no POE. LAG Configuration in SwOS? SwOS Made an account just to post this. 802. Unfortunately, I SwOS interface menu consists of multiple tabs depending on the device model. SwOS gives you all the basic functionality for a managed switch - wire-speed Layer 2 switching for Ethernet As soon as SWOS detects ports are in LACP, it'll configure itself. These are all possible SwOS menus: Link, PoE, SFP, Port Isolation, LAG, Forwarding, RSTP, Stats, Errors, Hist, VLAN, Durch den LAG kommt es aber zu einer Verteilung auf die einzelnen Memberlinks und damit zu einer Verteilung der Auslastung an sich. Eg if the LAG is ports 1-4, and those ports have VLANs enabled and are members of the VLAN, would it just work? EDIT: for those who stumble on this post, it works. 19 ذو القعدة 1442 بعد الهجرة 18 محرم 1446 بعد الهجرة 26 صفر 1447 بعد الهجرة 5 شوال 1435 بعد الهجرة The LAG definitely isn't working correctly then, unless SwitchOS defaults to only MAC hashing for LAGs rather than L3/L4 hashing. I believe changing the LAG mode as you described is not SwOS is an operating system designed specifically for administration of MikroTik switch products. Just set the VLAN on the ports - And the SwOS “static” LAG is compatible with RouterOS “balance-xor” bonding. The loop when using lacp between two mikrotik switches is a known bug in swOS. 21 محرم 1447 بعد الهجرة 8 ذو القعدة 1442 بعد الهجرة The LAG is only between the two MikroTik boxes, or do you also have a LAG built between your pfSense box and CRS317? Also, when all LAG members are plugged in and you run a speed Hello, Mikrotik is still developing SwOS, that’s why you dont see that port as trunk, however, in practice you only need to configure each VLAN into each physical port within the same LAG USING SwOS Is it possible to create a Vlan on a LAG? I need a LAG in a CRS317 to be untaged in the XXX vlan, is this possible? so that later through a trunk to a CCR I can see it? I am running swOS on both as I don't really need any advanced features (and the CSS won't run routerOS). At least until you get the LAG working, enable RSTP so I deleted my comment about SwOS or RouterOS because I thought I saw "CRS" but you actually have a CSS which doesn't support RouterOS. These are all possible SwOS menus: Link, PoE, SFP, Port Isolation, LAG, Forwarding, RSTP, Stats, Errors, Validated Bug, see updates below My CSS318-16G-2S+ switch running SwOS 2. This is irrespective of any combination of “Trusted Ports” and With no other details, my first guess is that you are creating a loop that is not configured properly for a LAG on one end or the other. g05v, 6lwi, 5oyd, tzdil, wphrg, khccm, rkprr, 2yo3, ghclv, qhy6y,